Coval Ultimate Top Coat Concrete Coating

Shop All COVAL

Product Name

Price

Quantity

Coval Ultimate Top Coat, Gloss (1 GL)

SKU#: EX-UTCG1-01 MFR#: UTC-G1

In stock

$159.00

Coval Ultimate Top Coat, Gloss (5 GL)

SKU#: CG-UTCG5-05 MFR#: UTC-G5

In stock

$745.00

Product Highlights

Coval UTC (Ultimate Top Coat) is a thin film, single component coating designed to protect finished surfaces and decorative coatings from surface wear and harsh chemicals.

For use on Polished & Densified Concrete, Epoxy, Urethane, Marble, Stone, and Terrazzo
Protects finished surfaces/decorative coatings from wear and harsh chemicals
Easy spray application
Gloss finish

Return Policy

Shipping Policy

Same-day Shipping

Industry's Best Guarantee

Equipment Service & Repair

Free Technical Support

Product Description

Coval UTC (Ultimate Top Coat) is a thin film, single component coating designed to protect finished surfaces and decorative coatings from surface wear and harsh chemicals.
It is typically spray applied for larger areas but can also be applied with a foam brush or even a microfiber cloth by a skilled applicator for smaller applications like countertops. The coating is clear, is dry to touch in a few hours and typically will get to 98% of its full hardness in 48 hours depending on the conditions.

Coval UTC makes an irreversible covalent bond through the available polar groups in epoxies, urethanes, and paints. This prevents moisture, stains, chloride ion penetration, dirt, ice, acids, animal waste, and graffiti damage.

Coval UTC is now only available in a Gloss finish. To create a Satin or Matte finish, Coval offers a matting agent.

For 1 gallon containers: CG-MATTAGNT-EA
For 5 gallon containers: CG-MTA5G-EA

Recommended Uses:

Polished & Densified Concrete
Epoxy
Urethane
Marble
Terrazzo

Important Specifications:

Color: Clear/White for the Gloss and White for Satin and Matte
Finish: Gloss
Type: Solvent Base
Flash Point: (C Penskey-Martens closed Cup) - 9C/15F VOC: Less than 100 g/L
Semi - breathable

Usage

Application Types

Only use an acetone proof pump sprayer and chemical resistant hoses.

Spraying for Satin and Matte finishes: stir the contents thoroughly in the bottom of the container with a low-speed drill mixer. This is to re-suspend the matting agents that have settled to the bottom before pouring into the sprayer. Remove all particle filters in the sprayer to avoid clogging. Re-shake the pump sprayer every 10- 15 minutes to re-suspend the matting agents ensuring a consistent finish. Maintain an adequate PSI to create a consistent flow and finish. Maintain a 12-16” distance from the tip to the object. Be sure to filter the coating as you pour it into the sprayer to strain out fine particles in the matting agent. Use a random circular motion as you spray to avoid lap lines.

Spraying for Gloss finish: be sure that any overlap of the coating will not create the appearance of lines. This can be an issue on highly reflective floors where a thicker coating in one area will distort the light refraction. When applying the satin or matte we recommend using a cone tip on the sprayer and apply in a circular motion so that you do not create overlapping lines. We also recommend using a cone tip and applying in a circular motion on highly reflective floors.

Apply 4-5 mils wet film thickness and never allow puddling. It is always best to spray on a few mockups to get the feel of putting down this product before attempting an actual project. Be careful not to apply too thick or allow the product to puddle as this will cause too much surface tension and possible delamination.

Coverage: 250-350 sq. ft/gal - Coverage will vary depending on the porosity and texture of the substrate, as well as the applicator’s method of application.

Drying Time: (@ 77 F, 50% RH): Temperature, humidity, and film thickness dependent; the higher the humidity, the faster the dry time.

Touch: 1-3 hours
Walk on: 12-24 hours
Full Cure: 7 Days

Clean Up: Clean tools and flush equipment with acetone at least twice immediately after application. IMPORTANT - once the coating is dry the tools will not clean up with acetone or any other solvent.